Even more fun with the IBM 3690, Hemisphere Mode

So, have you heard of hemisphere mode?

Hemisphere Mode is an important performance optimization of the Xeon 6500 and 7500

processors. Hemisphere Mode is automatically enabled by the system if the memory

configuration allows it. This mode interleaves memory requests between the two memory

controllers within each processor, enabling reduced latency and increased throughput. It also

allows the processor to optimize its internal buffers to maximize memory throughput.

 

Hemisphere Mode is enabled only when the memory configuration behind each memory

controller on a processor is identical. Because the Xeon 7500 memory population rules

dictate that a minimum of two DIMMs are installed on each memory controller at a time (one on each of the attached memory buffers), DIMMs must be installed in quantities of four per

processor to enable Hemisphere Mode.

 Our consultant didn’t follow the four per processor rule….

But then it gets even more interesting.

So I have two quad port Ethernet adapters (Intel Ethernet Server Adapter I340-T4) of course I’m not lucky enough to have them install automagically with ESX so I need drivers.

After much, much googling I hit on this post http://blog.bradpeczka.com/2011/05/02/ibm-nics-in-vmware-esxi-4-04-1/ with a comment that they got it to work on their 3690 X5’s so at least I knew it was possible.

I was pretty sure that I wanted the 2.1.10.2 version as verified by http://partnerweb.vmware.com/comp_guide1/detail.php?device_cat=io&device_id=14747

I burned it, and then loaded it as an additional driver during the ESX install and that’s when it hung at “Status: 32% complete – Loading 34.storage-drivers”

Gah! So I tried all sorts of iterations, flipping ports, but luckily someone else had the answer on the forum.

http://communities.vmware.com/message/2005176

Even though it installed ESX just fine without the network drivers, once I included the network drivers the RAID drivers stopped working

Apparently this is a known issue with the new version of the firmware for the M1015 (which I of course flashed it to)…

http://www-947.ibm.com/support/entry/portal/docdisplay?lndocid=MIGR-5087330

So, download the updated megaraid driver, burn it to disk, http://downloads.vmware.com/d/details/dt_esx4x_lsi_megaraid_529/ZHcqYnR0amhiZGhwZA==#version_history

And now I can install ESX…. That was easy

About these ads

More fun with the IBM 3690 X5, Bad status has been detected on 2 physical drives

So…. normally you get a new IBM server. You download the update express CD (Except now you have to download the IBM ToolsCenter Bootable Media Creator) update everything in the system then pop in the ServerGuide CD http://www-947.ibm.com/support/entry/portal/docdisplay?lndocid=SERV-GUIDE and then configure the RAID Adapter.

But then I got this:

Bad Status has been detected on 2 physical drives. What is going on here? Did we get to bad drives shipped to us? That doesn’t seem likely?

So I try all sorts of things, after the whole mezzanine issue (LINK) I’m starting to suspect all of the hardware. But everything seems to check out OK.

Then I remembered vaguely reading something about the RAID and UEFI. And there it was page 362 of the 580 page manual

Create a drive RAID array before installation. The ServeRAID management interface is
accessible via UEFI settings, by selecting System Settings  Adapters and UEFI
Drivers.

You open up this abomination from the UEFI screen

 

Then it brings up a screen where you can configure your JBOD disks as unconfirmed good. At that point you can use serverguide to set up the RAID…. very annoying.

 

Follow

Get every new post delivered to your Inbox.

Join 232 other followers