Find this post interesting? Do you like interesting things? Maybe you would like my invention, a connectible candle called a WickBrick!
Get one here http://wickbrick.etsy.com/
I am by no means a Cisco expert, not even close… so take this post with a huge grain of salt. It hopefully will help you at least get close to what you want, which is Nic Teaming on your Vmware server.
In our case our vmware servers have 6 Nics, that are configured like this.
So vmnic0 (zero) is for the service console, nic1 is a service console and for vmotion, and nic2 – 5 are teamed for the virtual machines.
So, now on to the Cisco config. So by design, ESX handles the outgoing load balancing, but to get incoming load balancing you need to configure your switch. This post talks a little bit about it
http://virtrix.blogspot.com/2006/11/vmware-switch-load-balancing.html
And I think it is a similar setup. I notice that that post uses spanning-tree portfast trunk but I’m not sure what that does 🙂
So to configure your Cisco
telnet into your switch
put in your password
type en
put in your admin password
Ok, so we have three groups we wanted to setup, group 1 on ports 1-4 group 2 on ports 5-8 group 3 on 9-12
so type config t
then
int range G2/1 – 4 (notice there is a space between the 1 and the dash and the dash and the 4) (I believe the g is for gigabit)
channel-group 1 mode on (we had a consultant use access and then caused a network storm…. )
then type
exit
so if you type show run
you should see blade 2 ports 1 – 4 as part of channel-group 1 and the mode should be on
now type
interface port-channel1
sw tr en dot
sw mode tr
sw non
exit
and then
wr mem (to write out your settings)
Hopefully these notes help somebody out there!
You might also want to take a look at http://blog.scottlowe.org/2006/12/04/esx-server-nic-teaming-and-vlan-trunking/
Here is what my config looks like….
interface Port-channel1
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
!
interface Port-channel2
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
!
interface Port-channel3
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
!
interface GigabitEthernet1/1
!
interface GigabitEthernet1/2
!
interface GigabitEthernet2/1
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
channel-group 1 mode on
!
interface GigabitEthernet2/2
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
channel-group 1 mode on
!
interface GigabitEthernet2/3
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
channel-group 1 mode on
!
interface GigabitEthernet2/4
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
channel-group 1 mode on
!
interface GigabitEthernet2/5
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
channel-group 2 mode on
!
interface GigabitEthernet2/6
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
channel-group 2 mode on
!
interface GigabitEthernet2/7
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
channel-group 2 mode on
!
interface GigabitEthernet2/8
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
channel-group 2 mode on
!
interface GigabitEthernet2/9
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
channel-group 3 mode on
!
interface GigabitEthernet2/10
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
channel-group 3 mode on
!
interface GigabitEthernet2/11
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
channel-group 3 mode on
!
interface GigabitEthernet2/12
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
channel-group 3 mode on
!
Filed under: Applied IT | Tagged: cisco 4502, ESX 3.5, ether-channel, nic teaming | 4 Comments »
